![]() Support for the DOOR32 drop file format as well as generic sockets was added by Rob Swindell and *nix compatibility was added by Stephen Hurd. OpenDoors was one of the most popular C "door kits". The Beast's Domain can handle up to 250 simultaneous players. The Beast's Domain is a multiplayer, interactive, real-time, Rogue-like ANSI adventure game. Protected tables (to keep users from hogging the tables for themselves). Ive been trying to post on the Syncronix BBS looking for answers, but noone ever responds. You also have the option to not allow the computer to be on password Does SyncTerm support uploading multi-files when using a protocol that supports such, like Ymodem or Zmodem When I get to the file selection screen, I dont seem to find any way to select more than one file to send. Turned off completely, or allowed to play only on certain tables (at your Single player games are played against the computer. Protected for private games, and the "house" can take a configurable percentage Has a configurable bet limit, ante, and table limit. The game can have up to 6 players per table, and up to 25 tables. Some of their software has since been released as open source and has been imported into the Synchronet CVS tree under the xtrn directory.ĭomain Poker is a single/multi-player, real-time, 5 card draw poker game. Generally, the software is updated to use xpdev and run on the platforms that Synchronet does and then is left in the CVS tree without active development.ĭomain Entertainment was once one of the major companies which wrote addons specifically for Synchronet. The Synchronet project has shown a willingness to "adopt" third-party BBS related software into its CVS tree. It supports the use of TheDraw fonts, and can save to the Synchronet Control-A code format, but is generally considered too incomplete for serious usage. It uses xpdev and ciolib but is not yet complete. SyncDraw is an ANSI art editor which was initially a cleanup of an old version of MysticDraw. Using this program, SysOps can once again offer their BBSes via direct modem-to-modem connections. So calculating the CRC is simple, just multiply the 128 byte data number by 65536, divide by 69665 and the low order 16 bits of the remainder are the CRC. In an interesting full circle, direct dial-up support for Synchronet is available again as Rob Swindell wrote a modem to telnet gateway program (SEXPOTS) for this purpose. The low order 16 bits of the remainder becomes the 16 bit CRC. His first "big" contribution was an implementation of Borlands conio library to allow the configuration utilities which were originally written for DOS to run on the Unix-like platforms. He ported the BBS to FreeBSD and did much of the Linux development work. ZModem is typically more compatible with other ZModem implementations.In late 2001, Stephen Hurd (Deuce) joined the project initially as *nix developer. However, if you do use XModem (or YModem, but especially XModem), there are a number of variations, so you need to make sure you're using the same one. I typically avoid XModem some XModems don't even transfer the right number of bytes (but round up to a half-kilobyte), and don't transmit the filename. Using IP will probably be easier once you've got IP working, although getting to the point of having IP working might be a bit more challenging overall, so ZModem may be an excellent choice. That is a totally different communication design than trying to use raw serial communications like ZModem. Whenever I've used SCP, it's been using TCP/IP, which means that an IP address must be assigned to both sides. 8N1 is a very common setting, 7E1 a bit less so, but such settings must match. If so, then also verify the basic communications settings: communication at 2400 or 9600 might be more prone to work with many hardware than 115200. Can you get into a terminal program, and type on one end, and see the other end? If not, you may have issues that cannot be resolved with software: OpenBSD FAQ on Serial Connections states, "we offer one hint: just because the ends plug in doesn't mean it will work." So start by verifying that hardware works okay. For serial communications, like XModem/ZModem, I'd start with just basic communication.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |